Facilities

The test section of the KROTOS facility consists of a stainless steel test section bolted to lugs welded on the inner side walls of a stainless steel pressure vessel. The cylindrical pressure vessel, inner diameter 0.4 m, height, 2.21 m, has a thick flat bottom and a flanged flat upper head and is designed to withstand a static pressure of 2.5 MPa at 493 K. The cylindrical test section, inner diameter 200 mm, outer diameter 240 mm, closed at the bottom by either a flat plate or with a gas trigger device, can contain water up to a height of about 1.27 m (about 40 litres).



The KROTOS main objective is to provide basic experimental information on FCI phenomena relevant to severe accident situations in nuclear reactors.

Facility is in operation at CEA. KROTOS was transferred to CEA Cadarache at the end of the JRC-Ispra MFCI programme in 1999.

For the JRC-Ispra KROTOS performed experiments see https://stresa.jrc.ec.europa.eu/facilities/krotos.

Determination of the vaporization rate according to the composition and the thermodynamic conditions of the corium (with FP simulants) was the aim of the COLIMA (COrium LIquid and MAterials) experiments. The facility provided representative conditions of the aerosols suspended inside the containment of PWRs under a severe accident. According to the scientific objectives of each experiment, different configurations of the facility can be used: corium/materials interaction (concrete, ceramics), release of aerosols from the corium (simulating physical-chemistry of oxidic and metallic fission products, without radioactive isotopes except uranium).

COLIMA consists of 1.5m3 tank, where the maximum internal pressure can reach 0.3MPa. The corium can be melted in a crucible by a thermite reaction or an induction coil that can maintain it hot in order to provide a steady state situation up to 3000◦C. The crucible, designed to contain few kilograms of corium, is surrounded by a thermal shield ring and can be placed at the bottom or at the middle of the tank. The walls of the vessel tank are thermally controlled at 150◦C. Portholes, dedicated to the instrumentation, are located at its top, half height and bottom.

VITI (‘‘VIscosity Temperature Installation’’) experimental assembly: (1) VITI chamber, (2) graphite crucible, (3) ZrCcoating, (4) studied mixture, (5) graphite susceptor, (6) thermal shield, (7) support for crucible, (8) support for thermal shield, (9) inductance coil, (10) pyrometer – measure of Tcrucible, (11) pyrometer – measure of Tmixture, (12) data acquisition

The experiments were dedicated to the selected coating interaction with water reactor corium and with sodium fast reactor corium compositions.
VITI facility has been developed to measure viscosity, density and surface tension on corium up to 2600 C by aerodynamic levitation. But it is also used as small crucibles heating for material interactions tests. Samples of less than 100 g can be studied in VITI.

In the hypothetical case of a nuclear reactor severe accident, the reactor core could melt and form a mixture, called corium, of highly refractory oxides (UO2, ZrO2) and metallic or oxidized steel, that could eventually flow out of the vessel and mix with the basemat decomposition products (generally oxides such as SiO2, Al2O3, CaO, Fe2O3, …).
The VULCANO experimental facility is operated to perform experiments with prototypic corium (corium of realistic chemical composition including depleted UO2). This is coupled with the use of specific high-temperature instrumentation requiring in situ cross calibration.
Due to the complex behavior of corium in the solidification range, an interdisciplinary approach has been used combining thermodynamics of multicomponent mixtures, rheological models of silicic semisolid materials, heat transfer at high temperatures, free-surface flow of a fluid with temperature-dependant properties.
Twelve high-temperature spreading tests have been performed and analyzed. The main experimental results are the good spreadability of corium–concrete mixtures having large solidification ranges even with viscous silicic melts, the change of microstructure due to cooling rates, the occurrence of a large thermal contact resistance at the corium–substrate interface, the presence of a steep viscosity gradient at the surface, the transient concrete ablation. Furthermore, the experiments showed the presence of the gaseous inclusions in the melt even without concrete substrate. This gas release is linked to the local oxygen content in the melt which is function of the nature of the atmosphere, of the phases (FeOx, UOy, …) and of the substrate. These tests with prototypic material have contributed to the validation of spreading models and codes which are used for the assessment of corium mastering concepts.
Facility is in operation.